Linksys SPA3102 - PSTN to VoIP Setup Guide - VarPhonex Reseller Program

Help

Welcome
Common Topics
Knowledgebase
Configuration Guides
Glossary
Contact Us

Quick links:
User Guide Quick Installation Data Sheet Firmware v5.1.7 Firmware v5.1.10 Contact Linksys Manufacturer's Site

Linksys SPA3102 - PSTN to VoIP Setup

The SPA3102 supports one RJ-11 POTS (Plain Old Telephone Service) FXS port to connect an existing analog phone and 2 100BaseT RJ-45 Ethernet interfaces to connect to a home or office LAN, as well as an Ethernet connection to a broadband modem or router.

The SPA3102 FXS and FXO lines can be independently configured via software controlled by the service provider or the end user so that any VarPhonex user can call their virtual number and place a call on the local POTS line.

STEP 1
Connect one Ethernet cable from your SPA3102’s ETHERNET port to the Ethernet port on your computer.

*PLEASE NOTE* Do not connect any other cables to the SPA3102 during initial configuration. (Cable/DSL/Router or Analog phone cables) If you connect anything other than this one cable, you will not be able to log into the device.

Now we must determine the address for your device so that it can be accessed and configured with you browser. To do this, we will need to find out what gateway address the device has given your computer.

To find the current gateway:

WINDOWS XP

Click Start
Click Run
Type CMD and press <enter>
Type IPCONFIG and press <enter>

In the returned list of information please find the section labeled LOCAL AREA CONNECTION and write down the default gateway.

EXAMPLE

Ethernet Adapter Local Area Connection:

Connection-specific DNS Suffix
IP Address	192.168.0.2
Subnet Mask	255.255.255.0
Default Gateway	192.168.0.1

STEP 2
Open up the web browser on the computer that is connected to the device and enter in the gateway address given to you.

EXAMPLE

<IPADDRESS>

(where <IP ADDRESS> is replaced by the address that was given to you in STEP 1).

STEP 3
Click on “VOICE” Tab.

Click on “ADVANCED”.

STEP 4 Click on “PSTN Line” Tab.
Modify only the circled items of the following:

Proxy:

sip.varphonex.com

Register Expires:

300

Display Name:

Enter your full name.

Userid:

Enter the new virtual phone number that you just added to your account, as mentioned in the note above.

Password:

Enter the password that you chose when you signed up for VarPhonex service.

Linksys SPA3102 Configuration

STEP 5
Change the “Preferred Codec” to G729a. Also be sure that the “Use Pref Codec Only” option is set to NO.

Linksys SPA3102 Configuration

STEP 6
Verify that Dial Plan 2 is configured as follows:

(xx.)

Linksys SPA3102 Configuration

STEP 7
Change the "VOIP-To-PSTN Gateway Enabled" setting to YES.

STEP 8
Change the "VoIP Caller Default DP" to 2.

STEP 9
Make calls!

Copyright VarPhonex.com

WebPhone | SIP Termination | SIP Trunking | Join Now | Learn More | Site Map
Custom Solutions | Blog | Careers | About VarPhonex | News | e911 | Legal

VarPhonex offers the industry leading VoIP Reseller Program. We let you sell VoIP in your brand name including Internet phone service, SIP termination, SIP Trunking, International DID numbers and unlimited VoIP plans. We also offer prepaid phone service using our voice over IP system and an analog telephone adapter, softphone, PBX, Asterisk, Trixbox or other VoIP device which can use a SIP Trunk. VarPhonex white label VoIP solutions are designed so you can private label our home phone service, business phone service, call shops service and phone service for cyber cafes. VarPhonex is proud to support Internet telephony equipment including Sipura, Linksys, Cisco, Digium, Grandstream and more. We offer low cost A to Z rates and provide International VoIP termination along with DID phone numbers for private label resale.

| | | | | | | | | | | |