Linksys SPA8000 Telephony Device Configuration Guide

Help

Welcome
Common Topics
Knowledgebase
Configuration Guides
Glossary
Contact Us

Quick links:
Data Sheet Quick Install ATA Admin Guide Contact Linksys Manufacturer's Site

Linksys SPA8000

The Linksys SPA8000-G1 8-Port IP Telephony Device is a full featured Analog Terminal Adapter (ATA) for small business enterprises providing enhanced communication services via a broadband connection to the Internet.

The SPA8000 features eight RJ-11 FXS ports to connect analog telephones to IP-based data networks and includes a single multi-port RJ-21 50-pin connector offering an alternative connection choice when deploying the telephony gateway in varied environments. The device also has one 10/100Base-T RJ-45 Ethernet interface to connect to either a router or multi-layer switch.

STEP 1
Connect one end of the Ethernet cable (included) to the ETHERNET port of the SPA8000. Connect the other end to your Cable/DSL modem.

Connect one end of a different Ethernet cable to the AUX port of the SPA8000. Connect the other end to the Ethernet port (network card) of your PC.

Power on the cable/DSL modem and then power on the SPA8000.

STEP 2
Make sure your PC is setup to obtain an IP address automatically. This will allow your PC to obtain an IP address from your SPA 8000.

Linksys SPA8000 Configuration

To verify that your PC obtained the IP address correctly, run the IPconfig command at the command prompt. Your network configuration should look like the following figure:

Linksys SPA8000 Configuration

Where 192.168.0.1 is your SPA8000’s IP address.

If for any reason your PC has not obtained the IP address from the SPA8000 even though it is setup to obtain an IP address automatically, run the following commands from the command prompt:

To release any IP address from your network card:
Ipconfig/release

To renew the IP address:
Ipconfig/renew

STEP 3
Open your internet browser and type the following: http://192.168.0.1 and press enter.
Enter “admin” for the user and “admin” for the password.

STEP 4
A setup page will appear. Click on “WAN Setup”.

Linksys SPA8000 Configuration

Choose the Internet connection type depending on how your ISP assigns you your Internet Protocol (IP) number. When you have finished your settings, click on “Submit Changes”. When your Router Setup screen comes back up, you should be able to browse the Internet from your PC. If not, contact your ISP.

Linksys SPA8000 Configuration

STEP 5
Choose from the main menu “VOICE” and then “L1”.

Linksys SPA8000 Configuration

Enter your InPhonex Virtual Number into the User Id field and the InPhonex sip password into the Password field.

Repeat step 5 for L2 – L8.

Linksys SPA8000 Configuration

STEP 6
For the best voice quality, choose codec G729 and then select AVT for the DTMF method.

Linksys SPA8000 Configuration

STEP 7
Submit all changes.

STEP 8
Make calls!

VarPhonex offers the industry leading VoIP Reseller Program. We let you sell VoIP in your brand name including Internet phone service, SIP termination, SIP Trunking, International DID numbers and unlimited VoIP plans. We also offer prepaid phone service using our voice over IP system and an analog telephone adapter, softphone, PBX, Asterisk, Trixbox or other VoIP device which can use a SIP Trunk. VarPhonex white label VoIP solutions are designed so you can private label our home phone service, business phone service, call shops service and phone service for cyber cafes. VarPhonex is proud to support Internet telephony equipment including Sipura, Linksys, Cisco, Digium, Grandstream and more. We offer low cost A to Z rates and provide International VoIP termination along with DID phone numbers for private label resale.

| | | | | | | | | | | |